Design, construction, testing, inspection and operation of electrically heated and directly fired shell boilers
Tanks
Stage-wise / Final inspection/ Vendor
Assessment
IS 803:1976
ASME -Sec. VIII:2015; IS 2825:1969(R2017); PD 5500:2006; API 510:2014; API 572:2016; IS 804:1967 (R2003); ASME Sec IX:2015, ASME Sec V:2017, ASME Sec VIII:2015
IS 10987, 1992
API 620, 2013
API 650, 2013
ASME Sec VIII 2015
Rules for the construction of pressure vessels; Indian Standard for unfired pressure vessels;
British standard specification for unfired fusion welded pressure vessel
Rules for the construction of pressure vessels; Indian Standard for unfired
pressure vessels; British standard specification for unfired fusion welded pressure vessel
Code of fabrication, Practice for design, testing and installation, of under-ground/above-ground horizontal cylindrical
steel storage tanks for petroleum products
Design and Construction of Large, Welded, Low-Pressure Storage Tanks
Welded tanks for oil storage
Rules for construction of pressure vessels
Gas Cylinders
Stage-wise / Final inspection/ Vendor
Assessment
IS 8196, 2004
IS 15490, 2004
ISO 11119-3, 2013
ISO 9809-2010
ISO11439-2013
ISO4706-2008
NZS -5454-1989
BS EN 13322-1:2003+A1:2006
ISO11120-2015
BS EN 1442:2006 + A1:2008
DOT39:2017 + Gas Cylinder Rules:2020
DOT 4BW:1995; DOT4BA-2003,
Steel cylinders for compressed gases (atmospheric gases, hydrogen, high pressure liquefiable gases and dissolved acetylene gases)
Cylinders for on-board storage of compressed natural gas as a fuel for automotive vehicles
Gas cylinders – Refillable composite gas cylinders and
tubes -- Design, construction and testing -- Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450L with non-load-sharing metallic or non-metallic liners
Refillable seamless steel gas cylinders -- Design, construction and testing
High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles
Gas cylinders – Refillable welded steel cylinders
Standard requirements for lightweight steel automotive compressed natural gas cylinders
Transportable gas cylinders. Refillable welded steel gas cylinders. Design and construction. Carbon steel
Refillable seamless steel tubes of water capacity between 150 l and 3000 l -- Design, construction and testing
LPG equipment and accessories. Transportable
refillable welded steel cylinders for LPG. Design and
construction
Non reusable - non refillable cylinder
Code of Federal Regulations-- Welded steel cylinders made of definitely prescribed steels with electric-are welded
longitudinal seam. Including DOT 4BA
Pipes [Ductile, Cast Iron, Carbon Steel, Ferrous, nonferrous, alloy steel, Seamless & Welded (without or with addition of filler wire)]
Stage-wise / Final inspection/ Vendor
Assessment
IS 8329, 2000
IS 3589, 2001
ASTM A 53:2015
API 5L, 45th Edition 2012
ISO 2531:2009
ASTM A 746:2015
ASTM A 716, 2015
ASTM A 74, 2015
API 5L, 45th Edition 2012
IS 1239-1:2004; IS 1239-2:2011, ASTM A 106:2019; ASTM A 333:2018
Centrifugally cast (spun) ductile iron pressure pipes for water, gas and sewage
Steel pipes for water and sewage
Seamless and Welded Standard Steel Pipe
Specification for line pipe
Ductile iron pipes, fittings, accessories and their joints for water applications
Ductile Iron Gravity Sewer Pipe
Ductile Iron Culvert Pipe
Cast Iron Soil Pipe and Fittings
Specification for line pipe
Seamless, Welded Pipes
Distillation Columns
Stage-wise / Final inspection/ Vendor
Assessment
IS 11556:2005
ASME SEC VIII 2015
Distillation column
Rules for construction of pressure vessels
IAF Scope 18 Machinery and Equipment Valves
Stage-wise / Final inspection/ Vendor
Assessment
API 614, April 2008
API 598-2016 Tenth Edition
IS 9890, 1981
IS 778:1984,
API 594:2017;
API 6FA:2020;
API 607:2016;
API 608:2020;
API 609:2017
BS EN12266-1 -2012
API 600, 2015
API 602, 2015
ASME B16.34, 2013
EN 12516, 2014
Lube Oil System Lubrication, Shaft-sealing and Oil-control Systems and Auxiliaries
Valve Inspection and Testing
General purpose ball valves
Copper alloy Gate, Globe and Check Valves for water works purposes.
Check Valves: Flanged, lug, wafer and butt welding.
Fire Test Specification for valves
Steel Gate Valves
Fire Test for quarter turn valve and valve equipped with non-metallic seat.
Metal ball valves
Butterfly valves
Testing of metallic valves.
Bolted bonnet steel gate valves for petroleum and natural gas industries
Compact Steel Gate Valves—Flanged, Threaded, Welding, and Extended-Body Ends
Electricity metering equipment, energy meters – testing, calibration, etc
MCC, Junction Boxes, Control Panels, Switch Gears,
Manufacture of electricity distribution and control apparatus e.g.
Switchgear (HT/LT), Panels, PCC, MCC, APFC VFD, CT, ,
Stage-wise / Final inspection/ Vendor
Assessment
IS 13947,2004;
IS 2147:1962
IS 8623-1, 1993
IS 12729, 2004
Low voltage switch gear and control gear; Degree of protection provided by enclosure for low voltage switch gear and control gear.
Low-Voltage Switchgear and Control Gear Assemblies, Part 1: Requirements for Type-Tested and Partially Type
Common High-Voltage Switchgear and Control gear
Standards
Low-voltage switchgear and control gear assemblies
Code of Practice for Electrical Wiring Installations
Code of practice for installation and maintenance of switchgear
equipments, Push Button Stations and Electrical lamps, Outdoor units and IPMS for Telecom sector,
Pressure Gauges, earthing , electrical resistance, Flameproof enclosure
IEC 61439:2011
IS 13947-5:2004
IS 9921:1985
IEC 62271:2011
Low-voltage switchgear and control gear assemblies - Part 1: General rules
Low-Voltage Switchgear and Control gear, Part 5: Control Circuit Devices and Switching Elements, Section 2: Proximity Switches
Alternating Current Disconnectors (isolators) and Earthing Switches for Voltages
High-voltage switchgear and control gear
luminaires and electrical installation classification etc.
IS 8623-1993
IS 13947-1:1993 (R2004)
IEC 62271-100,200 :2008
IS8623-1993
IEC60947 -2007
BIS IS 7987 -1985;
IEC 62271-100:2017;
EN 50152-1:2012
+ A1:2013
IS 2071-2:1974 (R2006)
IS2148-2004
EN 837 -1998
IS 10322 -2014
IEC60079 -2015
IS 3043 -1987
IS 5572 -2009
IEC
60529:1989+A1:1999+A2:2013
Low-Voltage Switchgear and Control gear Assemblies, Part 1: Requirements for Type-Tested and Partially Type-Tested Assemblies
Specification For Low-Voltage Switchgear And Control gear
High-voltage switchgear and control gear - Part 100: High voltage alternating-current circuit-breakers.
Low-Voltage Switchgear and Control gear Assemblies, Part 1: Requirements for Type-Tested and Partially Type-Tested Assemblies
Low-Voltage Switchgear and Control gear,
High-voltage switchgear and Control gear -All parts
Railway applications. Fixed installations. Particular requirements for alternating current switchgear. Circuit-breakers with nominal voltage above 1 kV
Methods Of High Voltage Testing
Electrical Apparatus For Explosive Gas Atmospheres - Flameproof Enclosures "d".
Stainless steel diaphragm pressure gauges
Luminaires Part 1 General Requirements and Tests
Electrical resistance trace heating -- General and testing requirements
Code of practice for earthing
Classification of hazardous areas (other than mines) having flammable gases and vapours for electrical installation.
Applies to the classification of degrees of protection provided by enclosures for electrical equipment
Manufacture of accumulators, primary cells and primary batteries like (UPS,
Battery, Battery chargers etc.)
Stage-wise / Final inspection/ Vendor
Assessment
IS1652:1991;
IS6303:1984;
IS1651:2013;
IEC60896-2011;
IS13514:2018;
IEC61982-4:2015
IS16242:2014;
IEC 62040-3:2011
IEC 60335-2-29:2004;
IEC 60086:2020
IS 6848:1979;
IEC-60335-2-29:2016+AMD1-2019
BIS IS 1651:1991 (R2002)
BIS IS 10918:1984 (R2003)
EN 50091-1-2:1998
IS13314-1992
Stationary cells and batteries, lead - Acid type with plante positive plates - Specification
Primary batteries – General
Stationary cells and batteries, lead - Acid type (With Tubular Positive Plates) - Specification
Stationary lead-acid batteries
Secondary batteries (Except Lithium) for the propulsion of electric road vehicles - Performance and endurance tests
Secondary batteries (except lithium) for the propulsion of electric road vehicles - Part 4: Safety requirements
Uninterruptible power systems (UPS): Part 1 general and safety requirements for UPS
Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements
Household and similar electrical appliances – Safety
Primary batteries
Lead Acid Batteries, Battery Chargers, UPS
Specification for stationary cells and batteries, lead-acid type with tubular positive plates
Specification For Vented Type Nickel Cadmium Batteries
Uninterruptible Power Systems (ups) - General And Safety Requirements For Ups Used In Restricted Access Locations
Manufacture of industrial process control equipment e.g. (PLC, DCS, CCTV, Fire & Gas detection system etc.)
Stage-wise / Final inspection/ Vendor
Assessment
NFPA 72-2016
IEC 584-1982
IS11360 -1985
National Fire Alarm and Signaling Code
Thermocouple Extension & Compensating Cable
Specification for Smoke Detectors for Use in Automatic Electrical Fire Alarm System
Manufacture of Optical Fibre Cables,
Instruments
Stage-wise / Final inspection/ Vendor
Assessment
IS/IEC 60794-1-1-2001
Fibre Optics, Fibres, Cables and Devices
Cables
Stage-wise / Final inspection/ Vendor
Assessment
IS1554-1988; IS7098-2011; IS9968:2002, IS694:1990, IS 14255:1995 (R2015)
IEC-60099-4, IS-3070 (Part III)
IS731:1971 (R2016)
PVC Insulated (Heavy Duty) Electric Cables
Lightning Arrestors
Specification for Porcelain insulators for overhead power lines with a nominal voltage greater than 1000 V
Measuring Instruments Ammeter, Voltmeter.
Stage-wise / Final inspection/ Vendor
Assessment
IEC 60051:2018
Measuring Instruments Ammeter, Voltmeter.
a) Manufacture of electric motors, generators and transformers
Stage-wise / Final inspection/ Vendor
Assessment
Other Codes , specifications
and standards relevant to category
Applicable national & international codes and standards, such as PESO, DMRI,
FM, BASSEFA, BIS, OISD Codes, IE Rules,
National Building Code, NEMA, EIL, TEIL, ARAMCO, MOZ Specs, etc., and customer requirements, QAP/ITP.
b) Manufacture of electricity distribution and control apparatus
Stage-wise / Final inspection/ Vendor
Assessment
IS 17036 : 2018; IS 1885:1971; IECPub50(25):1965; IS 7118 : 1973
Electricity distribution and control
IAF Scope 26- Gas Supply 26 A(iii) of NABCB Sub-sector categorization
Gas Supply- NGPL
Stage-wise/
In-service
PNGRB’s GSR 808(E) dated 11.11.2009 along with latest amendments, national/ international
standards mentioned therein and relevant statutes
PNGRB’s GSR 612(E) dated 27.08.2008 along with latest amendments,
national/ international standards mentioned therein and relevant statutes
IAF Scope 28- Infrastructure/ Construction a)Site preparation F 45.1
Stage-wise / Final inspection/ Vendor
Assessment
IS 456-2000
Plain & Reinforced concrete - Code of Practice
b)Building of complete constructions or parts thereof; civil engineering F 45.2
BS EN 13501-1:2007+A1:2009
Fire classification of construction products and
building elements. Classification using test data from reaction to fire tests
c) Building installation F 45.3
Morth -Fifth Edition
Specification of Road and Bridge works
d) Building completion F 45.4
IS 1786-2008
Concrete Reinforcement specification
e) Renting of construction or demolition equipment with operator F 45.5
IS 383-2016
Specification of Coarse and Fine aggregate for concrete
f) Renting of construction or demolition
equipment with operator F 45.5
BS EN 598-2004
Sampling and examination of bituminous mixtures for roads and other paved areas.
g) Site Preparation, Building construction /Civil Engineering, Building Installation, Building completion, Construction of transmission towers (Power and Telecommunication) including
stringing activities, Civil Engineering: Roads and Bridges, Audit of building construction.
IS13920-2016
IS 1343-2012
Ductile Design & Detailing RC structures
Pre-stressed concrete - Code of practice
Building – construction site preparation, completion and installation.
Road – Bituminous and Concrete
RCC reservoirs
Pipe Line Laying
Stage-wise / Final inspection/ Vendor
Assessment
IS 11134:1984
IS 15916 : 2011
IS 15917 : 2010
IS 16231 : 2019
Code of practice for setting out of buildings
Building Design and Erection Using Prefabricated Concrete - Code of Practice
Building design and erection using mixed/ composite construction - Code of practice
Code of Practice - Use of Glass in buildings
Machinery foundation
IS 7740 : 1985
IS 11682 : 1985
- Part 1 - General Methodology for Selection
- Part 2 - Energy and Light
- Part 3 Fire and Loading
Code of practice for construction and maintenance of road gullies
Criteria for design of RCC staging for overhead water tanks
Construction of Transmission towers (Power and Telecom) – Tower foundations
Stage-wise / Final inspection/ Vendor
Assessment
IS 10297 : 1982
IS 11384 : 1985
IS 11233 : 1985
IS 4091 : 1979
IS 1080 : 1985
IS 11089 : 1984
Code of practice for design and construction of floors and roofs using precast inforced / prestressed concrete ribbed or cored slab units
Code of Practice for Composite Construction in Structural Steel and Concrete
Code of practice for design and construction of radar antenna, microwave and TV tower foundations
Code of practice for design and construction of foundations for transmission line towers and poles
Code of practice for design and construction of radar antenna, microwave and TV tower foundations
Code of practice for design and construction of
The following offices of Apave TIV India Pvt. Ltd. is/are included under accreditation
Top management functions, quality management functions, administration & accounts. Key activities as applicable to head office.
Marketing, contract review, planning for inspection & nomination of inspection personnel, conduct of inspection, issuance of inspection report and inspection certificate
